G3 Cookie Skydive Camera Mount


The G3 Cookie Skydive Mount is the best solution for mounting every single model of GoPro onto a G3 Cookie Helmet. This camera mount is easy to install, even easier to remove, and non-destructive. The design utilizes a packing tool as the means for cutting away the camera in the advent of an entanglement. The ability to use the same G3 Cookie helmet for skydiving during the day, and then later at night take the camera mount off for some in-door skydiving tunnel time. The camera can be adjusted for belly flying on one jump, and then adjusted right back on the next for some free-flying. Never worry about smashing the camera into the ceiling of the airplane again. Gaining those precious extra inches of headroom the taller skydivers need in the plane. Never need to ask “Is my GoPro on” because the screen is actually visible while wearing the helmet. Have the ability to open the G3’s visor all the way, instead of only being able to open the visor halfway. The strength of the Spartan Chin’s uniquely 3D printed plastic is currently unmatched in the market. Finally, there’s a very handy packing tool holding that GoPro on the helmet. Especially handy when landing off, or jumping into a Pro-Rated Demonstration skydive.

GoPro Low Profile Mounting Buckle – Required

In both of the two images above, on the right is the required ‘GoPro Low Profile Mounting Buckle’. On the left is the standard GoPro mounting buckle. The Spartan Chin requires the GoPro ‘Low Profile Mounting Buckle’ for proper installation. On Amazon.com Prime, the official ‘GoPro Low Profile Mounting Buckle’ is included with the “GoPro Grab Bag” and only costs $19. Also, I highly recommend only purchasing official GoPro products. I have found that knock-off GoPro parts fail to meet the necessary tolerances and quality standards that the official GoPro parts more than exceed. Expect issues like sloppy mounting, weaker plastic, and difficultly remove the camera from the frames with the cheaper knock-offs GoPro mounting buckles and skeleton frames.


An updated installation video is in the works

Camera Mount Video

The video below was shot with an older prototype and a session 5 that I was jumping in Australia winter 2017/2018, or rather ‘Downunder’s summer.’

Color Options

Parts List

H3 Hummer

Valve Stem Tire Caps
H3 Hummer factory valve stem tire caps with seal gasket

Pack of 5 OEM H3 & H3T Valve Stem Tire Caps with rubber gasket

Add to cart
Skid Plates, Under Body Protection, H3 Hummer

2nd Generation 1/4 inch thick and 4-Foot Long by 2-Foot wide skid plates to protect the H3 Hummer underbody

Add to cart
Rock Sliders H3 Hummer

Heavy-duty rocker panel protection for the serious off-road enthusiast.

Add to cart
OnStar Microphone Adapter H3 Hummer

An adapter that makes it easy to connect the Factory OnStar Microphone to an aftermarket Radio

Add to cart
Modular Tire Carrier

Adjust the spare tire height from 31-inches to 39-inches, pre-cut holes for mounting. Future Hi-lift, CB-antenna, shovel, Jerry Can, and bottle opener brackets in development.

Add to cart
Light Bar Brackets H3 Hummer

Simple bolt-on light bar brackets for the H3 Hummer.

Add to cart
HVAC Instrument Panel Light Bulbs

An exact replacement for burnt out OEM HVAC Instrument Panel Light Bulbs, five to a pack.

Add to cart
H3 Hummer Hidden Winch Mount

Mount an 8,000lb or bigger winch inside the factory H3 Hummer bumper. Synthetic rope recommended.

Add to cart
H3 Backup Camera Mount

A simple mounting bracket for hiding a backup camera inside the factory tire.

Add to cart
Extended Leaf Spring Shackles H3 Hummer

Lift the rear suspension 1 1/2 inches, matches a front torsion bar crank perfectly.

Add to cart
4th Gen High Clearance Leaf Spring Bolt Plate H3 Hummer

4th Gen - Better ground clearance, stronger bracket, off-road improved shock mounting location

Add to cart


Skydiving Mini Packing Tool

A convenient packing tool for closing skydiving containers. Fits nicely inside the pocket on the reserve side ring cover.

Add to cart
G3 Cookie Skydive Camera Mount

Non-destructive easy-to-install camera mounts for the G3 Cookie Helmet with packing tool.

Select options
CSC’s Legends Jersey

2021 CSC Legends Boogie Jersey

Select options
Bonehead Aero Helmet Camera Mount

Camera mount for the Bonehead Composites Aero skydiving helmet

Select options


WordPress Theme Semper Fi

An opensource WordPress theme that can be used on your website.

Add to cart
WordPress Theme Adventure

WordPress Theme that tries to persuade the user that they're not sitting behind a computer.

Add to cart