The Spartan Chin is the best solution for mounting all versions of the GoPro Hero cameras to a G3 Cookie Helmet. The mount is easy to install, easy to remove. It utilizes a packing tool for the means of cutaway-way the camera in the advent of an entanglement. Gain the ability to use the Cookie for skydiving, and then later that night inside the indoor skydiving tunnel. Adjust the camera for RW one jump, and then adjust it again on the next jump for freefly. Stop smashing the camera into the ceiling of the airplane. Having the extra headroom is super important for us taller skydivers. Never ask again, "Is my GoPro on" because the screen is actually visible while wearing the helmet. Have the ability to open the G3's visor all the way again, instead only being able to open G3 visor halfway. The strength of the uniquely 3D printed plastic of this camera mount is currently unmatched. Finally, when landing off or jumping in that o-so-awesome Pro-Rated Demonstration skydive have a packing tool handy to close the rig.

The OnStar Microphone Adapter makes connecting the GM factory microphone to an aftermarket radio easy. Not just for the H3 Hummer, the OnStar Microphone Adapter works plenty other GM vehicles. This adapter probably works if the vehicle has a similar looking microphone. Otherwise, don't worry because the OnStar Adapter can be returned to me if it doesn't work. To connect the adapter to the microphone, just disconnect it from the wiring harness. Plug in the OnStar Microphone Adapter to the microphone and then run 3.5mm male-to-male headphone jack to the back of the radio.

Super heavy duty rocker panel protection rock slider for the H3 Hummer protect the body right below the doors. Bounce the Hummer off rocks, trees, and whatever happens to get stuck underneath there without worrying about damage. Built to take a beating, the square tubing is a quarter inch thick, the mounts are a half inch thick, the circle tubing is standard DOM roll cage tubing .2 inches thick and they weight in at 84lb. each. Basically, never worry about crushing the rocker panels again.

The H3 Quick n’ Simple Auxiliary Audio Input is a plug and play 3.5mm audio input wiring harness for the H3 Hummer factory radio. This wiring harness only minutes to install, works flawlessly, and is easy to use. Once installed, just plug a standard 3.5mm headphone jack in the wiring harness and the other end into your phone. Press the button labeled "Band" on the factory radio until you see "XM". Do not worry, an XM-Sirus satellite subscription isn't necessary for the Quick n' Simple Auxiliary Input. When done listening to the music on the phone, just unplug the 3.5mm headphone jack and XM-Sirus satellite will work normally again.

The H3 Hummer High Clearance Leaf Spring Mounts completely replace the entire rear axle leaf spring bolt plate. Designed to be used with 2" longer shackles but not required, these mounts eliminate all the issues with the factory leaf spring mount. An increased ground clearance protects from ripped up leaf spring mounts, stops broken U-Bolts, bend shock mounts, and allows for the factory spec shock ride height with the optional longer shackles. The Leaf Spring Mounts are laser cut from 1/4 inch steel and bent with relief cuts out of one solid piece of metal, making it a part that's bolted on and forgotten about.

Fix that dark spot on the H3 & H3T Dashboard at night with the HVAC Instrument Panel Light Bulbs, sold as a pack of 5. The HVAC Instrument Panel Light Bulbs are direct replacements for the burnt out HVAC light bulbs on GM HVAC Dashboards, 4x4 Controls, and also the Door Lock / Window Controls. These light bulbs are only held on to the PCB board by a quarter turn which makes these light bulbs extremely quick and easy to replace. Be sure to contact me for any issues with replacing the light bulbs in your H3 HUMMER.

The H3 Hummer Hidden Winch Mount bolts on to the Hummer with no permanent modification required to mount an 8,000lb. winch. The winch mount is excessively strong, made from 3/8" steel for unquestionable strength and reliability. Secured in place with 4 bolt massive bolts, 2 x ⁵/₈" and 2 x ³/₄". Easily installed in a day, and most of that time is just properly relocating the control box solenoid. Designed to used with an Aluminum Hawse Fairlead and Synthetic Rope, providing the best in safety and strength. In stock, and ready to ship.

Lift the rear suspension 1 ¹/₄ inches with these shackles for the H3 Hummer. Extended 2 inches longer than the factory, these shackles help out with maintaining the forward rake after leveling the front-end for better gas mileage and gaining those extra few inches for off-road. These shackles add extra confidence in tight turns because of the strength that these ¹/₄ inch thick steel and ¹/₈ inch braced shackles give you over the factory stamped shackles.

Slide over rocks and through the mud without getting stuck, with ¹/₄ inch thick skid plates extending the H3 Hummer Under Body Protection 4' x 2', completely protecting the transmission and transfer case from damage. The skid plates come painted black, and with to brackets for mounting. Huge, flat, and smooth, these skid plates truly shine in the deep mud or snow helping you to easily slide on down the trail, when the 35" tires just can't quite reach the ground.

All of the theme's on WordPress.org are created, developed, and maintained free of charge by the author. The author of this theme, Schwarttzy, offers a premium version that includes additional features to enhance your experience. This premium version of Semper Fi Lite supports the author by offsetting the many hours of work being put into the theme. For incentive, the premium version of Semper Fi Lite includes additional features to customize the theme with. Many of these options, list of these options are just below, are not available in the free version. Additionally, the author has offered to make minor custom changes to the Semper Fi Lite code for further customization. However, the author is still going to support the free versions when issues of bugs or errors in the code are found.

Thank you for downloading and installing the WordPress Theme "Adventure." I hope that you enjoy it and that I can continue to create these beautiful themes for years to come. But, if you could take a moment and become acutely aware that I have created this Theme and other themes free of charge, and while I'm not looking to get rich, I really like creating these themes for you guys. Which is why I offer additional customization of "Adventure" when you support me and install the "Adventure+" on your WordPress. If you're interested in supporting my work, or need some of the addition features in "Adventure+" just purchase it using the "Add to Cart" button above. Thanks again, Eric Schwarz

A classy, yet simple solution to mounting a backup camera on an H3 Hummer. With this mount, the camera hides in plain sight. Protected from the elements and also damage. All the while offering up the perfect view when backing up. It also removes the guesswork while squeezing into a small parking spot. Helps with backup to a tow hitch on the first try, instead of leaving everyone with the illusion that it's our first time behind the steering wheel. With the camera mount, it's one less nuisance to deal with every time the H3 is driven. Making life... just a little bit easier.